Wifi chuyên dụng Aruba IAP-305 là dòng wifi công nghiệp hàng đầu thế giới thuộc tập đoàn HPE – MỸ. Với việc hỗ trợ băng thông AC lên tới 1600Mbps tíchhợp 6 antena MIMO giúp cho wifi chuyên dụng Aruba IAP-305 có khả năng phát sóng và chịu tải lớn. Sản phẩm được sử dụng trong những công trình lớn như các Ngân hàng, Resort, Khu du lịch…
Specification IAP – 305
WI-FI Radio Specifications |
• AP type: indoor, dual radio, 5GHz 802.11ac 3×3 MIMO and 2.4GHz 802.11n 2×2 MIMO
• Software-configurable dual radio supports 5GHz (Radio 0) and 2.4GHz (Radio 1) • 5GHz: Three spatial stream Single User (SU) MIMO for up to 1,300Mbps wireless data rate to individual 3×3 VHT80 client devices • 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 300Mbps wireless data rate to individual 2×2 HT40 client devices • Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio • Supported frequency bands (country-specific restrictions apply): – 2.400 to 2.4835GHz – 5.150 to 5.250GHz
– 5.250 to 5.350GHz
– 5.470 to 5.725GHz
– 5.725 to 5.850GHz
• Available channels: Dependent on configured regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum • Supported radio technologies: – 802.11b: Direct-sequence spread-spectrum (DSSS) – 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• Supported modulation types:
– 802.11b: BPSK, QPSK, CCK – 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (conducted) transmit power (limited by local regulatory requirements): – 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2×2) – 5GHz band: +18 dBm per chain, +21 dBm aggregate (2×2)
– NOTE: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
• Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver performance • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance • Short guard interval for 20MHz, 40MHz and 80MHz channels • Space-time block coding (STBC) for increased range and improved reception • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput • Transmit beam-forming (TxBF) for increased signal reliability and range • Supported data rates (Mbps): – 802.11b: 1, 2, 5.5, 11 – 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
– 802.11n: 6.5 to 300 (MCS0 to MCS15)
– 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80 • 802.11n/ac packet aggregation: A-MPDU, A-MSDU |
WI-FI Antennas | Three integrated dual-band downtilt omni-directional antennas for 3×3 MIMO with maximum antenna gain of 3.9dBi in 2.4GHz and 5.4dBi in 5GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. |
Other Interfaces | • One 10/100/1000BASE-T Ethernet network interface (RJ-45) – Auto-sensing link speed and MDI/MDX • 802.3az Energy Efficient Ethernet (EEE) |
Power Sources and Consumption | • The AP supports direct DC power and Power over Ethernet (POE) • When both power sources are available, DC power takes priority over POE • Power sources are sold separately • Direct DC source: 12Vdc nominal, +/- 5% – Interface accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length • Power over Ethernet (POE): 48 Vdc (nominal) 802.3af/802.3at compliant source – When using IPM, the AP may enter power-save mode with reduced functionality when powered by an 802.3af POE source (see details on Intelligent Power Monitoring elsewhere in this datasheet) – Without IPM, the USB port is disabled when the AP is powered by and 802.3af POE source • Maximum (worst-case) power consumption: 13W (POE) or 12W (DC) • Maximum (worst-case) power consumption in idle mode: 3.7W (POE) or 2.6W (DC) |
Mounting | • The AP ships with two (white) mounting clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling. • Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details |
Mechanical |
Dimensions/weight (unit, excluding mount accessories):
– 165mm x 165mm x 38mm
– 460g
|
Environmental |
• Operating:
– Temperature: 0° C to +50° C (+32° F to +122° F) – Humidity: 5% to 95% non-condensing
• Storage and transportation:
– Temperature: -40° C to +70° C (-40° F to +158° F) |
Regulatory | • FCC/Industry of Canada • CE Marked • R&TTE Directive 1995/5/EC • Low Voltage Directive 72/23/EEC • EN 300 328 • EN 301 489 • EN 301 893 • UL/IEC/EN 60950 • EN 60601-1-1 and EN 60601-1-2 |